Screw
From Freepedia
- This article refers to the threaded fastener. For other meanings, see Screw (disambiguation).
A screw is a shaft with a helical groove or thread formed on its surface. Its main uses are as a threaded fastener used to hold objects together, and as a simple machine used to translate torque into linear force. It can also be defined as an inclined plane wrapped around a shaft.
Contents |
Threaded fastener
A screw used as a threaded fastener consists of a shaft, which may be cylindrical or conical, and a head. The shaft has a helical ridge or thread formed on it. The thread is essentially an inclined plane wrapped around a shaft. The thread mates with a complementary helix in the material. The material may be manufactured with the mating helix (tapped), or the screw may create it when first driven in (a self-tapping screw). The head is specially shaped to allow a screwdriver or wrench to grip the screw when driving it in. It also stops the screw from passing right through the material being fastened and provides compression.
Screws can normally be removed and reinserted without reducing their effectiveness. They have greater holding power than nails and permit disassembly and reuse.
A screw that is tightened by turning it clockwise is said to have a right-hand thread. Screws with left-hand threads are used in exceptional cases, when the screw is subject to anticlockwise forces that might undo a right-hand thread. Examples include rotating items such as the left hand grinding wheel on a bench grinder or the left hand pedal on a bicycle (both looking towards the equipment).
Threaded fasteners are traditionally made by a cutting action such as taps and dies provide, however recent advances in tooling allows them to be made by rolling the blank (a section of rod) between two specially machined dies. The thread form and shape of the fastener are squeezed onto the blank. (Surprisingly, shot pellets can be made in a similar fashion.) This method work hardens the threads and saves material, but there are those who believe the cut product was superior.
Bolt
A bolt is a cylindrical (not conical) threaded fastener that passes through the work piece and is held in place by a nut or a threaded hole on the other side. This is a very common way of holding together temporary and permanent constructions. An unthreaded hole is known as a clear hole. See also bolted joint.
The thread on a bolt sometimes occupies only part of the shaft, the remainder of the shaft being clear.
Other fastening methods
When screws and bolts cannot be used, nailing, riveting, roll pins, pinned shafts, welding, soldering, brazing, and gluing are all alternatives.
Materials and strength
Screws and bolts are made in a wide range of materials, with many varieties of steel being perhaps the most common. Where great resistance to weather or corrosion is required, stainless steel, titanium, or bronze may be applied. Some types of plastic, such as nylon or Teflon, can be threaded and used for fastening requiring moderate strength and great resistance to corrosion or electrical insulation. Even porcelain and glass can have molded screw threads that are used successfully in applications such as electrical line insulators.
The same type of screw or bolt can be made in many different grades of material. For critical high-tensile-strength applications, low-grade bolts may fail, resulting in damage or injury. On SAE-standard bolts, a distinctive pattern of marking is impressed on the heads to allow inspection and validation of the strength of the bolt. However, low-cost counterfeit fasteners may be found with actual strength far less than indicated by the markings. Such inferior fasteners are a danger to life and property when used in aircraft, automobiles, heavy trucks, and similar critical applications.
Mechanical analysis
A screw is a specialized application of the wedge or inclined plane. It contains a wedge, wound around a cylinder or shaft, that either fits into a corresponding inclined plane in a nut, or forms a corresponding inclined plane in the wood or metal as it is inserted. The technical analysis (see also statics, dynamics) to determine the pitch, thread shape or cross section, coefficient of friction (static and dynamic), and holding power of the screw is very similar to that performed to predict wedge behavior. Wedges are discussed in the article on simple machines.
Critical applications of screws and bolts will specify a torque that must be applied when tightening. The main concept is to stretch the bolt, and compress the parts being held together, creating a spring-like assembly. The stretch introduced to the bolt is called a preload. When external forces try to separate the parts, the bolt sees no strain unless the preload force is exceeded (this takes some effort to imagine).
As long as the preload is never exceeded, the bolt or nut will never come loose (assuming the full strength of the bolt is used). If the full strength of the bolt is not used (e.g., a steel bolt threaded into aluminum threads), then a thread-locking adhesive may be used.
If the preload is exceeded during normal use, the joint will eventually fail. The preload is calculated as a percentage of the bolt's yield tensile strength, or the strength of the threads it goes into, or the compressive strength of the clamped layers (plates, washers, gaskets), whichever is less.
Tensile strength
Screws and bolts are usually in tension when properly fitted. In most applications they are not designed to bear large shear forces. For example, when two overlapping metal bars joined by a bolt are likely to be pulled apart longitudinally, the bolt must be tight enough so that the friction between the two bars can overcome the longitudinal force. If the bars slip, then the bolt may be sheared in half, or friction between the bolt and slipping bars may erode and weaken the bolt (called fretting). For this type of application, high-strength steel bolts are used and these should be tightened with a torque wrench.
High-strength bolts usually have a hexagonal head with an ISO strength rating (called property class) stamped on the head. The property classes most often used are 8.8 and 10.9. The number before the point is the tensile ultimate strength in MPa divided by 100. The number after the point is 10 times the ratio of tensile yield strength to tensile ultimate strength. For example, a property class 5.8 bolt has a nominal (minimum) tensile ultimate strength of 500 MPa, and a tensile yield strength of 0.8 times tensile ultimate strength or 0.8(500) = 400 MPa.
Tensile ultimate strength is the stress at which the bolt fails (breaks in half). Tensile yield strength is the stress at which the bolt will receive a permanent set (an elongation from which it will not recover when the force is removed) of 0.2 %. When elongating a fastener prior to reaching the yield point, the fastener is said to be operating in the elastic region; whereas elongation beyond the yield point is referred to as operating in the plastic region, since the fastener has suffered permanent plastic deformation.
Mild steel bolts have property class 4.6. High-strength bolts have property class 8.8 or above.
The size and property class of a bolt used for a specific application are dependent on a variety of factors, including availability, spatial constraints, and whether the load is static or dynamic. An M10, property class 8.8 bolt can very safely hold a static tensile load of about 15 kN.
Types of screws and bolts
- Cap screw, used where strong holding power is essential has a convex head, usually hexagonal, designed to be driven by a spanner or wrench, but also made as flat head.
- Wood screw has a tapered shaft allowing it to penetrate undrilled wood.
- Lag screw or lag bolt is a large wood screw with a hexagonal head, driven by a wrench rather than a screwdriver.
- Machine screw has a cylindrical shaft and fits into a nut or a tapped hole; a small bolt.
- Self-tapping screw or thread cutting screw has a sharp thread and that cuts its own hole, often used in sheet metal or plastic. They usually have a notch at the tip, through several threads, that aids in chip removal during thread cutting.
- Thread rolling screw has a lobed cross section (instead of round). They form the threads (rather than cutting) during installation. They are usually used in steel holes.
- Drywall screw is a specialized self-tapping screw with a cylindrical shaft that has proved to have uses far beyond its original application.
- Set screw, used to prevent loosening due to vibration, available with thumb screw, square head, Allen head (inset socket) and, most commonly, headless, designed to be inserted flush with or below the surface of the work piece.
- Dowel screw is a wood screw with two pointed ends and no head, used for making hidden joints between two pieces of wood.
- A stud is similar to a bolt but without the head. Studs are threaded on both ends. In some cases the entire length of the stud is threaded, while in other cases there will be an unthreaded section in the middle. It may be anchored in concrete, for example, with only the threads on one end exposed.
- A carriage bolt or coach bolt has a domed head and the shaft is topped by a short square section under the head. It is used in wood where the square section is pulled into the wood as the nut is tightened, preventing the bolt from turning.
- A stove bolt is similar to a carriage bolt, but usually used in metal. It requires a square hole in the metal being bolted to prevent the bolt form turning.
- Superbolt is a form of very large fastener where tension in the bolt is developed by a special nut containing individual jack screws. This is applied in large structural joints where hand tools or portable tools are insufficient to develop the required tension of a simple bolt and nut.
- Acme screw form has threads that are stronger and broader than standard V-profile threads, making them much better for load carrying, linear actuating (also see ball screws), and quick threading. It is often used for vise screws.
Shapes of screw head
(a) pan, (b) button, (c) round, (d) truss, (e) flat, (f) oval
- pan head: a low disc with chamfered outer edge.
- button or dome head: cylindrical with a rounded top.
- round head: dome-shaped, commonly used for machine screws.
- truss head: lower-profile dome designed to prevent tampering.
- flat head or countersunk: conical, with flat outer face and tapering inner face allowing it to sink into the material.
- oval or raised head: countersunk with a rounded top.
- bugle head: similar to countersunk, but there is a smooth progression from the shaft to the angle of the head, similar to the bell of a bugle.
- cheese head: disc with cylindrical outer edge, height approximately half the head diameter.
- fillister head: cylindrical, but with a slightly convex top surface.
- socket head: cylindrical, relatively high, with different types of sockets (hex, square, torx, etc.).
- mirror screw head: countersunk head with a tapped hole to receive a separate screw-in chrome-plated cover, used for attaching mirrors.
- headless (set screw): has either a socket or slot in one end for driving.
Some varieties of screw are manufactured with a break-away head, which snaps off when adequate torque is applied. This prevents tampering and disassembly and also provides an easily-inspectable joint to guarantee proper assembly.
Types of screw drive
Modern screws employ a wide variety of drive designs, each requiring a different kind of tool to drive in or extract them. The most common screw drives are the slotted and Phillips; hex, Robertson, and torx are also common in some applications. Some types of drive are intended for automatic assembly in mass-production of such items as automobiles. More exotic screw drive types may be used in situations where tampering is undesirable, such as in electronic appliances that should not be serviced by the home repair person.
- Slot head has a single slot, and is driven by a flat-bladed screwdriver. The slotted screw is common in woodworking applications, but is not often seen in applications where a power driver would be used, due to the tendency of a power driver to slip out of the head and potentially damage the surrounding material.
- Cross-head, cross-point, or Phillips has a "+"-shaped slot and is driven by a cross-head screwdriver, designed originally for use with mechanical screwing machines. The Phillips screw drive has slightly rounded corners in the tool recess, and was designed so the driver will slip out, or cam out, under strain to prevent over-tightening. The Phillips Screw Company was founded in Oregon in 1933 by Henry F. Phillips, who bought the design from J. P. Thompson. Phillips was unable to manufacture the design, so he passed the patent to the American Screw Company, who was the first to manufacture it. A Frearson screw drive is similar to a Phillips but has a more pointed V shape. A JIS (Japanese Industry Standard) looks like a Phillips screw, but is not designed to cam out and will therefore be damaged by a Phillips screwdriver if it is too tight. Commonly found in Japanese equipment.
- Pozidriv is patented, similar to cross-head but designed not to slip, or cam out. It has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. Phillips screwdrivers will usually work in Pozidriv screws, but Pozidriv screwdrivers are likely to slip or tear out the screw head when used in Phillips screws. Pozidriv was jointly patented by the Phillips Screw Company and American Screw Company.
- Torx is a star-shaped or splined bit with six rounded points. These were found in early Apple Macintosh computers, to discourage home repairs. A "tamper-resistant" type of Torx head has a small pin inside the socket. This "torx pin" configuration is commonly used in prisons, other correctional facilities, and in government schools & facilities. The pin inside the socket is designed to stop the use of commonly available hand tools to remove the screws.
- Hexagonal (hex) socket head has a hexagonal hole and is driven by a hexagonal wrench, sometimes called an Allen key, or by a power tool with a hexagonal bit.
- Robertson head has a square hole and is driven by a special power-tool bit or screwdriver. The screw is designed to maximize torque transferred from the driver, and will not slip, or cam out. It is possible to hold a Robertson screw on a driver bit horizontally or even pendant, due to a slight wedge fit. Commonly found in Canada in carpentry and woodworking applications and in Canadian-manufactured electrical wiring items such as receptacles and switch boxes.
- Square-drive head is an American clone of the Robertson that has a square hole without taper. Due to the lack of taper, the hole must oversize relative to the screwdriver, and is much more likely to strip than the Robertson.
- Tri-Wing head has a triangular slotted configuration. They are for instance used by Nintendo on its Game Boys to discourage home repair.
- Torq-Set or offset cruciform is an uncommon screw drive that may be confused with Phillips; however, the four legs of the contact area are offset in this drive type.
- Spanner drive uses two round holes opposite each other, and is designed to prevent tampering. Commonly seen in elevators in the United States.
Lara Specialty Tools has a more extensive guide to 24 screw head types.
Tamper resistant screws
Image:Torx driver secure.png Many screw drives, including Phillips, Torx, and Hexagonal, are also manufactured in tamper-resistant form. These typically have a pin protruding in the center of the screw head, necessitating a special tool for extraction.
Image:Screws - tamper resistant slotted.jpg The slotted screw drive also comes in a tamper-resistant one-way design with sloped edges; the screw can be driven in, but the bit slips out in the reverse direction.
Tools used
The hand tool used to drive in most screws is called a screwdriver. A power tool that does the same job is a power screwdriver; power drills may also be used with screw-driving attachments. Where the holding power of the screwed joint is critical, torque-measuring and torque-limiting screwdrivers are used to ensure sufficient and not excess force is developed by the screw. The hand tool for driving cap screws and other types is called a spanner (UK usage) or wrench (US usage).
Screw measurements
There are many systems for specifying the dimensions of screws, but in much of the world the ISO preferred series metric has displaced the many older systems.
Metric screws
The diameter of a ISO preferred series screw is specified in millimetres (mm) prefixed by the capital letter M, as in "M6" for a 6 mm diameter screw.
The pitch of metric threads varies according to the diameter, but not absolutely regularly. Some examples: a M3 thread has a 0.5 mm pitch, M4: 0.7 mm, M6: 1 mm, M10-12: 1.5 mm, M14-16: 2 mm, M18-22: 2.5 mm.
The diameter of a metric screw is the outer diameter of the thread. The tapped hole (or nut) into which the screw fits, has an internal diameter which is the size of the screw minus the pitch of the thread. Thus, an M6 screw, which has a pitch of 1 mm, is made by threading a 6 mm shaft, and the nut or threaded hole is made by tapping threads in a 5 mm hole.
Metric screw threads are also available in "fine pitch" versions, sometimes several pitches for one diameter (example: M18/fine in 1, 1.5 and 2 mm pitches). The fine thread series is deprecated and not recommended for use in new designs. The fine metric threads were once found in equipment made in the Far East, but that has changed with the standardisation of the ISO preferred thread series.
Non-metric screws
Before the metric system was common, many engineering companies had their own standard screw sizes. The first person to create a standard (in about 1841) was the English engineer Sir Joseph Whitworth. Whitworth screw sizes are still used, both for repairing old machinery and where a coarser thread than the metric fastener thread is required. This system had two thread sizes: coarse (BSW) and fine (BSF). The thread angle was 55°.
A later standard in the UK was the BA system, named after the British Association for Advancement of Science. Screws were described as "2BA", "4BA" etc., the odd numbers being rarely used. While not related to ISO metric screws, the sizes were actually defined in metric terms, a 0BA thread having a 1 mm pitch. These are still the most common threads in some niche applications. Certain types of fine machinery, such as moving-coil meters, tend to have BA threads wherever they are manufactured. Curiously enough, even though every other fastener on a camera may use metric threads, the tripod socket will likely be a 1/4"-20 thread.
The USA has its own system, usually called the Unified Thread Standard. A version of this standard, called SAE for the Society of Automotive Engineers, was used in the American automobile industry. The SAE is still associated with inch based fasteners by the public even though the U.S. auto industry (and other heavy industries relying on SAE) switched to ISO preferred series fasteners back in the 1970s and afterwards.
Screws are described as 4-40, 6-32, 8-32, 10-32, 10-24, etc. (for numeric sizes, odd numbers are rare), or 1/4"-20, 1/4"-28, etc. (for inch unit sizes), with the first number giving shaft diameter (numeric or inches) and the second number being threads per inch.
These screws are sometimes found outside the USA in older model personal computers based on the IBM PC specification. Since the computer industry is now based in Asia (mostly Taiwan), the industry now uses metric fasteners. As more and more products are made outside the U.S. and then imported into the U.S., the use of inch based fasteners is declining, and it is only a matter of time before the inch fastener series is gone forever.
Other thread systems include BSP (British Steam Pipe; used for other purposes as well) and CEI (Cycle Engineers Institute, used on bicycles in Britain and possibly elsewhere), NPT and NPTF (coarse and fine pipe threads), and PG (German: "Panzer-Gewinde"), used in thin plate metal, such as for switches and nipples in electrical equipment housings.
History
In antiquity, the Greek mathematician Archytas of Tarentum (428 – 350 BC) was credited with the invention of the screw. By the 1st century BC, wooden screws were commonly used throughout the Mediterranean world in devices such as oil and wine presses. Metal screws did not appear in Europe until the 1400s.
The metal screw did not become a common woodworking fastener until machine tools for mass producing it were developed at the end of the 18th century. The British engineer Henry Maudslay patented a screw-cutting lathe in 1797; a similar device was patented by David Wilkinson in the United States the next year.
Standardization of screw thread forms accelerated during WWII so that interchangeable parts could be produced by any of the Allied countries.
Though not screws, perhaps also see cotter or pin bolts, and "clinch bolts" (now called rivets), used in ship building prior to the mid 19th century.
See also
References
Henry H. Ryffel (ed.), Machinery's Handbook 23rd Edition, Industrial Press Inc. New York, 1988 ISBN 083111200X
External links
- Lara Tools screw types - Specialty tool dealer documents more than two dozen different screw heads, along with their drivers.
- boltdepot.com - Bolt grade markings and strength chart, metric and imperial.
